📍 Jubail, Eastern Province
Spreader Beam Inspection & Certification in Jubail
A spreader beam is a below-the-hook device that works in compression, with slings or shackles hanging vertically from each end so the lifting legs do not squeeze long or fragile loads such as pipe, precast units, cabins and modules. It is common in fabrication yards, pipe laydown areas and plant construction in Saudi Arabia, and many are fabricated locally to suit a particular job. A site-built beam without a design basis, weld records or a proof test is a real hazard, so independent inspection and load testing before first use are essential. Jubail Industrial City hosts the world's largest petrochemical complexes, requiring rigorous lifting and heavy-equipment compliance.
Spreader Beam inspection in Jubail: local context
Process plants in Jubail rely on chain blocks, lever hoists, lifting beams and winches for routine maintenance, from pulling pump and compressor components to handling heat exchanger bundles during shutdowns. Hoists left installed outdoors for long periods in heat, dust and humidity wear load chains, hooks and safety latches in ways that are easy to miss. EES examines hoists and lifting tools on site, verifies rated capacity and records results for plant maintenance teams.
Spreader Beam inspection scope in Jubail
- ✓Main beam for straightness, bowing, dents and local buckling of the web or flanges
- ✓Welds at the lifting lugs, padeyes and end fittings, visually and with MPI or dye penetrant where required
- ✓Padeyes and lifting lugs for hole elongation, wear, cracks, deformation and adequate edge distance
- ✓Adjustable beams: locking pins, pin holes and position markings for the rated configurations
- ✓Shackles and end connections for correct size, pin security and compatibility with the rated load
- ✓Section loss and corrosion, especially inside box sections, and condition of the coating
- ✓Marking of safe working load, self-weight, serial number and permitted sling angles
- ✓Design calculation or drawing, material certificates and previous test records
Defects commonly found
- ✓Cracked welds at padeyes or end plates
- ✓Beam bent or locally dented after an impact or an off-centre pick
- ✓Pin holes elongated or padeyes worn out of tolerance
- ✓Missing or illegible SWL and self-weight marking
- ✓Unauthorised weld repair or modification without re-testing
Standards
- ✓ASME B30.20 (Below-the-Hook Lifting Devices)
- ✓ASME BTH-1 (Design of Below-the-Hook Lifting Devices)
- ✓Manufacturer specifications and load charts
- ✓Saudi Aramco General Instructions (GI), where applicable
Testing
A proof load test is typically carried out at 100%-125% of rated capacity depending on the standard and client, with the beam checked for permanent deformation afterwards and critical welds examined by NDT where required.
Frequency
Typically a thorough examination at least annually, plus an inspection before first use and after any repair, modification or damage, with a visual check before each lift.
Who we support in Jubail
Local focus areas: Jubail Industrial City, Jubail Commercial Port and SABIC plants.
Explore more
Category: Hoists & Lifting Tools
FAQs
Can you inspect a spreader beam on site in Jubail?＋
Yes. Our inspectors travel to your yard or project site in Jubail, including Jubail Industrial City, Jubail Commercial Port and SABIC plants, so the equipment does not need to be moved.
Which industries in Jubail request spreader beam inspection?＋
Typically operators and contractors in the Eastern Province from these sectors: Oil, Gas & Petrochemical; Ports, Logistics & Warehousing; Manufacturing & Industrial.
Does a site-fabricated spreader beam need a design calculation?＋
Yes. A locally built beam should have a design basis that supports its rated capacity, along with material certificates and weld records. Inspectors will normally ask for these before carrying out the proof load test.
What is the difference between a spreader beam and a lifting beam?＋
A spreader beam works mainly in compression and keeps the sling legs vertical, with load hung from each end. A lifting beam works in bending with a lifting point at the centre and loads hung below it, usually to keep the load level.