📍 Al Ahsa, Eastern Province
Truck-Mounted Crane Inspection & Certification in Al Ahsa
Truck-mounted cranes place a telescopic boom crane on a standard truck chassis with a separate driving cab, and are one of the most common lifting machines for yard work, pipe delivery, maintenance and light construction across Saudi Arabia. Their capacity depends on the truck frame, subframe fixing and outrigger stability as well as the boom, and many operate with minimal maintenance in hot, dusty conditions. Independent inspection checks both the crane and the chassis it relies on. Close to the Shaybah and Ghawar fields, with growing industrial and logistics activity.
Truck-Mounted Crane inspection in Al Ahsa: local context
Cranes in Al Ahsa are often set up on sand or compacted desert ground, so outrigger bearing and ground preparation matter as much as the machine itself. Mobile and crawler cranes support shutdown and maintenance work at processing facilities and fabrication work in the Al Ahsa Industrial Area. EES examines the boom, wire rope, load chart and LMI function, and arranges load tests before cranes mobilise to a job.
Truck-Mounted Crane inspection scope in Al Ahsa
- ✓Chassis frame and crane subframe mounting bolts, welds and any unauthorised modifications
- ✓Power take-off, hydraulic pump and drive-line, plus hydraulic tank level, filters and oil condition
- ✓Front and rear outriggers or stabilisers, extension beams, cylinders and the outrigger-extended interlock
- ✓Telescopic boom, wear pads and extension synchronisation, boom angle and length sensors
- ✓Load moment indicator or overload device and anti-two-block, including the calibration against test weights
- ✓Hoist rope, drum, hook block, safety latch and hoist brake holding
- ✓Slew bearing, slew gearbox and swing brake and lock
- ✓Truck brakes and air system, tyres, steering, lights and cab-side crane controls
Defects commonly found
- ✓Cracked or loose crane subframe mounts and chassis modifications without engineering approval
- ✓Outrigger cylinder leakage or missing outrigger interlock allowing crane use with outriggers retracted
- ✓Worn hydraulic pump or PTO giving low relief pressure, slow boom response and hot, contaminated oil
- ✓Boom wear pads worn out and hydraulic hose abrasion on the boom or turntable
- ✓Hoist rope worn at the end terminations or at sheaves, and non-functioning hook safety latch
Standards
- ✓ASME B30.5 Mobile and Locomotive Cranes
- ✓EN 13000 Cranes - Mobile cranes
- ✓OSHA 29 CFR 1926 Subpart CC (Cranes and Derricks in Construction)
- ✓Manufacturer specifications and load charts
Testing
A rated-capacity load test is typically carried out at 100%-125% of rated capacity at selected radii, depending on the standard and client, with the chassis, outriggers and overload device observed during the lift.
Frequency
Typically at least annually, with a check before mobilisation to a new site and more frequent inspection for units on heavy daily duty.
Who we support in Al Ahsa
Local focus areas: Hofuf and Al Ahsa Industrial Area.
Explore more
Category: Cranes
FAQs
Can you inspect a truck-mounted crane on site in Al Ahsa?＋
Yes. Our inspectors travel to your yard or project site in Al Ahsa, including Hofuf and Al Ahsa Industrial Area, so the equipment does not need to be moved.
Which industries in Al Ahsa request truck-mounted crane inspection?＋
Typically operators and contractors in the Eastern Province from these sectors: Oil, Gas & Petrochemical; Manufacturing & Industrial.
What is the difference between a truck-mounted crane and a mobile crane?＋
A truck-mounted crane uses a standard truck chassis and a PTO-driven hydraulic system, while many mobile cranes use a purpose-built carrier. They are generally inspected and tested under the same mobile crane requirements.
Why does a truck-mounted crane inspection include the truck chassis?＋
The crane's rated capacity relies on the chassis frame, subframe fixing, brakes and tyres. Cracked or modified chassis members can invalidate the load chart, so they are part of the inspection.